seekerbas.blogg.se

1. Mptool i 5188 v.5 serial number#
2. Mptool i 5188 v.5 install#
3. Mptool i 5188 v.5 update#
4. Mptool i 5188 v.5 driver#
5. Mptool i 5188 v.5 pro#

Use of hand-held roofing torch is recommended as it affords a good control. Torchingīituplus ULTRA P5180 membranes are installed by using a cylinder fed propane gas torch. Side overlaps should be a minimum of 100 mm and the end overlap 150mm. Begin membrane application by unrolling the roll of Bituplus ULTRA P5180 membrane and aligning the side laps. All overlaps at the membrane seams shall be installed so as to have «up» slope laps over «down» slope lap. Start the installation of all membrane plies from the low point or drains, so the flow of water is over or parallel to the plies, but never against the lap. In addition to that the primer also acts as a binder for the dust which gets accumulated on the concrete surface even after cleaning. As the viscosity of the primer is low, it easily penetrates into the concrete pores which promotes the adhesion between the membrane and the concrete surface. Allow the primer to dry prior to the application of the membrane. PrimingĪpply Polyprime SB* (Solvent based primer) 4- 6 m²/L to a clean smooth and dry surface by brush, roller or spray. All surface imperfections, protrusions, structurally unsound and friable concrete must be removed and repaired. The surface shall be cleaned thoroughly of all contaminants like dust, traces of curing compound, oil and grease. This simply means a high level close-knit interlocking between cells and uniform distribution of polymers that result in excellent adhesion of the molten bitumen compound during application, even on vertical surfaces. With the state-of-the art homogenizing facility, the bitumen compound is enriched on its cohesive links at microscopic level. In order to offer a superior sealing of the overlap joints, the polyester used as the carrier is positioned in a carefully chosen position, while the innovative enhanced thermofusible film applied on the membrane has clear demarcation lines for proper alignment of the membranes with the recommended overlap area. The right blend of the high quality bitumen and polymers, coupled with various reinforcements, provides excellent resistance to high hydrostatic pressure and better flexibility, strength and heat resistance. The Bituplus ULTRA range of waterproofing membranes has been developed with special selected components and advanced technologies, in order to offer premium quality and superior features and performance, even under extreme conditions. If your hub is still not detected, please contact our support for additional assistance, we’re more than happy to help!SBS modified bituminous waterproofing membraneīituplus ULTRA E5180 is an elastomeric high performance bitumen based torch applied waterproofing membrane.

Mptool i 5188 v.5 update#

Mptool i 5188 v.5 driver#

Computers that are equipped with older Texas Instruments, Fresco Logic, Etron, or Wistron USB 3.0 host controllers may be unstable with USB 3.0 hubs even with the latest driver updates.

Mptool i 5188 v.5 pro#

(older Mac Pro systems with PCI-e USB 3.0 add-on cards may not supported because of limitations in their driver support for USB 3.0 hubs) Mac users may update through a Boot Camp installation.Updating through a virtual machine like Parallels, VMware, VirtualBox, etc is not supported as USB pass-through mode is not available for hubs.Users should consult their computer or motherboard manufacturer for the latest drivers, or contact our support for help. Please note that Windows Update does not usually download these drivers.

Mptool i 5188 v.5 install#

This firmware update utility is only compatible with Microsoft Windows operating systems.įor macOS and Linux users please contact our support for additional assistance, we’re more than happy to help!įirmware update to improve compatibility with some ASMedia USB 3.0 host controllers with roll-up firmware changes from 2020. Installation instructions in the readme.pdf included in the zip file.

Mptool i 5188 v.5 serial number#

This update is not necessary for most NVMe SSDs which do not use the Phison chipset.Īpplicable to enclosures with serial number starting with 2645-A# and up. Firmware update to address incompatibility with Phison E7 and E12 based NVMe SSDs, including some SSDs from Silicon Power.